Quick Facts

  • Manufacturer: Mobileye.
  • Product: Shield+.
  • Equipment type: Camera-based blind-spot and collision-warning system.
  • Primary purpose: Provide warnings about supported vulnerable road users in monitored blind spots.
  • Sensing: Multiple vehicle-mounted cameras.
  • Driver interface: Visual and audible warnings.
  • Primary section: Safety Systems.
  • Compatibility: Confirm vehicle eligibility, camera layout, system generation, and installation requirements.

Overview

Mobileye Shield+ is designed for large commercial and municipal vehicles operating around vulnerable road users. Its camera arrangement monitors supported blind-spot areas and warns the driver when relevant hazards are detected.

The driver remains responsible for checking mirrors, observing the surroundings, and taking appropriate braking or steering action. A warning system does not establish that every hazard will be detected.

This page describes the product family. The exact generation, camera layout, configuration, and applicable manual determine the capabilities of an individual installation.

Key Characteristics

  • Provides additional awareness around monitored blind spots.
  • Requires a vehicle-specific camera arrangement.
  • Uses an in-cab warning interface.
  • Must be identified by generation and configuration.
  • Should be evaluated separately from active braking and steering equipment.

Major Components

Mobileye’s Shield+ product information describes external cameras, a forward camera unit, left and right blind-spot warning displays, and an EyeWatch interface. Match the complete equipment list to the installed version.

  • Approved camera equipment and mounts.
  • Processing and control electronics.
  • Driver warning displays and audible outputs.
  • Power, signal, and communication harnesses.
  • Application-specific configuration.
  • Any separately specified connected-service equipment.

Product Type and Construction

Review Shield+ as a complete installed warning system. Camera position, vehicle geometry, displays, wiring, and configuration should be assessed together.

A general-purpose side camera is not sufficient evidence of equivalent detection capability. Match approved replacement parts and service procedures.

Sensor, Hardware, and Software Design

Record camera identities, mounting positions, controller information, and available software records before comparing equipment or arranging repairs.

Do not assume that similar-looking Mobileye components share the same functions. Confirm the exact generation and approved installation.

How the Safety System Works

Camera information is analyzed to identify supported road users and assess relevant warning conditions. The driver receives information through the fitted warning interface.

The driver must assess the situation and take action. The absence of a warning should never be treated as clearance to turn or change lanes.

Position and Function Within the Vehicle

Verify camera and display locations using the approved installation layout. Check the relationship between camera views, mirrors, bodywork, and accessories.

Assess rear visibility and full tractor-trailer coverage separately. Cameras mounted around a cab do not automatically establish monitoring along every part of an attached trailer.

Common Specifications

A useful specification identifies the vehicle, equipment generation, and approved camera layout. Obtain numerical values from the applicable documents.

  • Vehicle make, model, model year, and identification number.
  • Shield+ generation and configuration.
  • Camera count, identities, and positions.
  • Documented warning areas.
  • Supported road-user categories.
  • Operating speeds and lighting requirements.
  • Driver-interface arrangement.
  • Electrical, setup, and calibration requirements.

Detection Coverage and Operating Performance

Confirm coverage through the installed system’s documentation. Separate a camera’s viewing area from the conditions under which a warning is generated.

Do not describe the system as unrestricted 360-degree detection or guaranteed full-trailer protection without application-specific evidence.

Pedestrian, Cyclist, and Motorcyclist Awareness

Mobileye describes blind-spot warnings for pedestrians, cyclists, and motorcyclists. Confirm supported detection conditions for the installed version.

Do not assume the same blind-spot function detects every vehicle, fixed obstacle, or other object. Review each intended use against the documented capability.

Operating Speeds and Activation Conditions

Check operating speeds, lighting requirements, and activation conditions separately for front and side functions. Use the manual for the exact hardware and configuration.

Do not transfer night-detection claims or speed thresholds between Shield+ generations. Confirm the applicable requirements before describing availability.

Warning Functions and Alert Behavior

Mobileye describes yellow caution indications and red collision-risk indications accompanied by audible warnings. Drivers should learn the meaning of the fitted interface.

Respond to the surroundings rather than waiting for a particular warning level. Continue using mirrors and safe turning procedures.

Blind-Spot Warnings and Active Intervention

Shield+ should be presented as driver-warning assistance. Automatic braking and corrective steering require separately documented equipment.

When comparing systems, list warning, braking, and steering capabilities individually. Similar safety terminology does not establish identical vehicle responses.

Forward Warning Functions

Mobileye’s Shield+ page also lists forward collision, lane departure, headway, forward pedestrian and cyclist, and speed-limit functions. Verify the enabled features through installation records.

Explain front and side warnings separately during familiarization. Their coverage, operating conditions, and driver indications should not be assumed identical.

Camera and Event-Recording Functions

Verify live camera views, stored video, and footage access independently. Cameras used for hazard detection do not automatically establish a surround-view display or recording service.

If separate recording equipment is fitted, document its hardware, storage, services, and relationship to the warning system.

Electrical Requirements, Wiring, and Connections

Use approved diagrams for power, grounds, camera connections, warning displays, and vehicle inputs. Match replacement harnesses and connectors to the application.

Inspect external cable routing and cab connections. Repairs should preserve approved protection and avoid interference with visibility or controls.

Vehicle Network and System Integration

Identify required vehicle inputs and communication arrangements through the applicable installation guide. Investigate missing inputs alongside camera and display condition.

Verify external integrations separately. A vehicle-data connection does not establish automatic control, video recording, or ELD compliance.

Fleet Connectivity and Safety Reporting

Confirm whether connected reporting is fitted and supported for the installation. Identify the provider, hardware, account access, and service terms.

Keep the primary product page under Safety Systems and cross-link it from Telematics and ELD Systems when connected capabilities are relevant.

Review alert reports with route conditions and driver observations. Counts and mapped events should be interpreted in their operating context.

Controls, Indicators, and Driver Feedback

  • Identify the fitted displays and warning outputs.
  • Learn normal startup and status indications.
  • Understand front and side warning meanings.
  • Review permitted driver settings.
  • Recognize unavailable assistance and fault information.

Driver Controls and System Availability

Follow the correct manual for settings and controls. Do not change installation parameters through unsupported methods.

A quiet warning interface does not confirm clear surroundings or correct operation. Drivers must continue observing traffic directly.

System Status, Fault Indicators, and Diagnostics

Record indications, symptoms, and recent service work before changing settings or replacing components. Identify the affected camera or warning area where possible.

Use authorized support procedures and complete required verification after repair.

Materials, Environmental Protection, and Durability

Inspect camera housings, lenses, mounts, cables, and connectors. Check component-specific cleaning and environmental requirements.

Review body repairs and accessory changes against the approved camera layout. Preserve the required viewing areas.

Duty Cycle and Operating Conditions

Consider turning frequency, urban traffic, delivery stops, and interactions with vulnerable road users when evaluating equipment.

Match the documented functions to actual routes and provide familiarization when drivers move between differently equipped vehicles.

Mounting and Installation

Confirm vehicle eligibility and use approved camera heights, positions, orientations, and mounting hardware. Preserve driver visibility when positioning displays.

Do not relocate cameras solely for convenience. Have changes reviewed against the installation requirements.

Calibration and Configuration

Determine setup and calibration requirements from the exact installation guide. Retain configuration and verification records.

After camera movement, replacement, windshield work, or relevant body repairs, follow the applicable checks before relying on the installation.

Vehicle and System Compatibility

Confirm compatibility through Mobileye or an authorized provider using vehicle identification and body details. Broad retrofit descriptions do not replace an application check.

Review camera positions, available vehicle inputs, supported coverage, and current service arrangements before purchase.

Related Component Compatibility

Verify cameras, processing equipment, displays, mounts, wiring, and configuration together. Confirm connected-service equipment independently.

Similar branding does not establish interchangeability between Shield+, Shield+ Connect, Mobileye 8 Connect, or other Mobileye products.

Common Applications

  • Eligible large commercial vehicles.
  • Approved municipal and transit applications.
  • Fleets evaluating vulnerable-road-user warning equipment.
  • Operators maintaining documented Shield+ installations.

Advantages

  • Adds warning information around supported blind spots.
  • Provides a defined system for reviewing vulnerable-road-user awareness.
  • Offers manufacturer documentation for installation and operating review.

Limitations or Considerations

  • Coverage depends on the approved camera layout.
  • Detection conditions must be confirmed by generation.
  • Warnings do not establish that every hazard is detected.
  • Recording and connected services require separate verification.
  • Drivers remain responsible for observation and vehicle control.

Driver and Operator Experience

Explain warning meanings, monitored areas, and operating limitations before assigning the vehicle. Use the installed generation’s documentation.

Encourage reports that describe the road user, maneuver, warning behavior, and conditions. Specific observations support training and service evaluation.

Inspection and Wear Points

  • Camera lens and housing condition.
  • Mounting security and orientation.
  • Obstructions from bodywork or accessories.
  • External harness routing and connectors.
  • Display condition and visibility.
  • Recent installation, windshield, or body-repair records.

Maintenance and Ownership Notes

Retain installation, calibration, component, and diagnostic records. Include camera and warning-interface condition in routine reviews.

For a used vehicle, confirm equipment identity and support arrangements. Review prior body repairs that may have affected camera positions.

Common Safety System Problems

Diagnostic review should consider camera view, mounting changes, wiring, vehicle inputs, configuration, and display operation. Follow the applicable troubleshooting process.

Record persistent symptoms and obtain qualified support rather than assuming a failed camera from one unexpected warning.

Safety and Service Precautions

Follow Mobileye and vehicle-manufacturer instructions for installation, electrical work, and camera service. Secure the vehicle and use qualified personnel.

Never create a close encounter with a pedestrian, cyclist, or other road user to test warnings. Use approved verification procedures.

Identification Information

Collect vehicle identification, system generation, camera identities, installation positions, software information, and configuration records. Match these to the appropriate support literature.

Buying Considerations

  • Confirm the exact Shield+ generation.
  • Verify vehicle eligibility and installation support.
  • Review camera layout and warning coverage.
  • Check operating and lighting requirements.
  • Inspect equipment and calibration records.
  • Confirm parts, service, and connectivity support.
  • Provide driver familiarization.

Variants and Configurations

Identify the installed generation, camera arrangement, enabled functions, and any connected-service package. Do not combine specifications from different manuals into a universal feature list.

Comparison to Similar Equipment

Compare blind-spot systems by supported road users, monitoring areas, operating conditions, warning presentation, and installation requirements. Camera-based recognition and radar-based detection should be evaluated by their documented capabilities.

Best Fit For

  • Operators maintaining supported Shield+ installations.
  • Fleets evaluating vulnerable-road-user warning equipment.
  • Eligible large vehicles operating in busy urban environments.
  • Buyers reviewing vehicle-specific blind-spot assistance.

Related Vehicle and Trailer Types

These links provide vehicle background and do not establish Shield+ compatibility or trailer coverage.

Related Truck and Trailer Models

Explore these profiles for general equipment context. Confirm retrofit eligibility independently for each vehicle.

Related Safety System Types

Related Safety System Products

Related Equipment Systems

Related Guides

Regulatory and Compliance Notes

Confirm applicable requirements and approved installation arrangements for the individual vehicle. A product name or warning function alone does not establish compliance.

Real World Operating Notes

Review warnings alongside road-user position, maneuver, lighting, vehicle configuration, and system status. Detailed reports help distinguish operating limitations from service needs.

Maintain safe mirror checks and turning procedures throughout the fleet, including in vehicles with warning assistance.

Frequently Asked Questions

Is Shield+ the same as Mobileye 8 Connect?

No. Confirm the exact product and camera arrangement rather than treating related Mobileye equipment as interchangeable.

Does Shield+ provide automatic braking?

Present Shield+ as warning assistance. Verify any active braking equipment separately.

Does it detect every object beside the truck?

Do not assume universal object detection. Check the supported road users and monitoring conditions for the installed version.

Does every version have the same night capability?

Confirm lighting and detection requirements through the correct generation’s manual.

Does it provide live side-camera video?

Verify video-display and recording capabilities separately from hazard detection and warning indications.

Availability and Where to Find

Contact Mobileye or an authorized provider for current equipment availability, vehicle eligibility, installation support, replacement parts, and connected-service information.

Support Trucking Families

Truck Equipment Atlas supports the mission of Grey Cross, a nonprofit dedicated to helping families of truck drivers who lose their lives while on the road. As the site grows, part of its mission is to bring awareness and support to these families.

Video Overview

Truck Equipment Atlas will continue expanding with video overviews and equipment breakdowns to help drivers and fleets better understand commercial truck safety systems.

Follow the Growth of Truck Equipment Atlas

Truck Equipment Atlas continues to expand with new truck profiles, trailer coverage, diesel engine pages, equipment system resources, manufacturer information, and educational guides.

Visit our Site Updates page to explore recent additions, project milestones, and upcoming resources as we continue building one of the industry’s growing commercial trucking equipment reference libraries.

View the Latest Site Updates: Truck Equipment Atlas Site Updates

Scroll to Top